- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- June 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- June 2016
- May 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- July 2015
- May 2015
- April 2015
Get in touch with the Kentra team
Kentra deliver all types of horticulture courses from chainsaws to mowers check out our website for more course inf… https://twitter.com/i/web/status/9964000724756725763:41 PM May 15th
Quick hitch devices on excavators
This month we are supporting #Safetember, See danger, speak up! the initiative launched by the Fork Lift Truck Association and backed by the HSE with events throughout the month. We will also be issuing articles relating to the Construction industry and related features. We hope you enjoy and find the this months Kentra news features of interest.
This article describes what a quick hitch is, discusses common failure modes, in particular with semi-automatic hitches.
A QH or quick hitch on an excavator is a latching device that enables attachments to be connected to the dipper arm of the plant and interchanged quickly. An excavator operator may change the bucket on his excavator up to 30 times a day in order to maximise the machine productivity.
A significant number of all accidents investigated on excavators are attributed to the bucket detaching from a QH and injuring a ground worker, most of which are fatal and major injuries. However, there may be many more dangerous occurrences that occur that might not be reported when a bucket detaches unintentionally from the hitch, but without injury because no one is underneath at the time.
HSE Inspectors ask the following questions when assessing the safe management of QH use:
● They ask site supervision if the QHs on the excavators under their control require a manual safety pin (they should know)
● Is the risk of bucket detachment covered by their risk assessment?
● In addition to evidence of training in operating the excavator, have excavator operators been trained in the use of their QHs, and, where appropriate, in the use of the excavator as a crane?
● Is there a checklist in the cab of daily and weekly inspection and maintenance carried out on the excavator, and does this checklist include a check of the QH and lubrication as appropriate? Is there a record of the inspection and maintenance actually carried out?
● What are their management systems for checking whether manual safety pins are always in place?
● Whether the safety pins are inserted where appropriate. (If the pin is missing, try looking behind the driver’s seat!)
● Can the operator explain the type of QH system they have (do they know whether it needs a safety pin or not?) and is a manual or instruction card available in the cab?
● Does the operator know how to visually check that the QH is locked?
● Does the operator know that, for all types of QH, they should test the security of the bucket after changing it? [Some manufacturers advise “shake, rattle and roll”, others suggest placing the bucket flat on the ground then trying to uncrowd the bucket so that the bucket tries to disengage from the QH].
If inspectors suspect that the QH is malfunctioning or has parts missing evidenced by:
● The latch on hydraulic types moving in a jerky action;
● Any obvious missing or broken parts; or
● Hydraulic pipes close to the hitch badly damaged.
Then inspectors should request involvement of their local SG mechanical specialist.
Typically, the QHs are not made by the excavator manufacturer, although some QHs are ‘badged’ with the excavator manufacturer’s name and are supplied by them. There are known to be 20 or more manufacturers on the market, most of whom have several different designs of QH.
A standard bucket is secured to the dipper arm with two pins. QHs may pick up a standard bucket using the original pins, or the QH may have a dedicated attachment system that only fits buckets with matching engagement lugs. The advantage of dedicated systems is that the original radius of bucket movement can be maintained by compensating for the thickness of the QH, thus keeping the same break out force as the manufacturer intended. The disadvantage is less flexibility because only dedicated buckets can be used. In addition, a significant investment in dedicated buckets and attachments is required. For this reason most systems are ‘pin’ type rather than dedicated type.
Quick hitch devices on excavators
The QH systems on the market can be manual or non-manual. Non-manual systems are known as semi-automatic and automatic:
A manual system requires the operator to change the bucket by, for example, winding a screw thread to open and close a latch, or using a bar to open a spring actuated latch. Although faster than the conventional method of bucket change, this method is relatively slow and cannot be done from the excavator cab.
Non-manual systems use a hydraulic ram to move the latch to retain the bucket.
Semi-automatic systems require the operator to leave his cab after he has operated the QH latch to insert a retaining pin in the hitch as additional security. This pin usually works by locking the latch in its closed position; this is often referred to as the “safety bar” and it is not a load bearing part of the hitch. The safety pin cannot be inserted unless the latch is in its fully closed position.
Automatic systems can be operated entirely from the cab and usually have an independent locking system which functions automatically and which does not rely on hydraulic pressure to hold the latch in its closed position. Automatic systems should have a method where the operator can verify that the hitch is locked from the cab – for example, locking pins may protrude from the side of the hitch when the latch is in its unlocked state. Large attachments such as rammers may prevent the locked condition being verified from the cab, in which case, the driver needs to get out of his cab to check the locked condition.
QH systems have become increasingly common and now many large excavators and some mini-excavators are fitted with QHs. QHs need to be maintained and may well be replaced during the life of an excavator. If they are replaced, then it is important that the controls are compatible with the new hitch, or are replaced at the same time.
Although incidents have occurred with automatic QHs, accident statistics suggest that the majority of incidents occur on semi-automatic systems where a manual safety pin should be inserted, but where the operator failed to do so.
Picture of buckets used with Quick hitch devices on excavators
If the QH is used for lifting (many QH’s have a lifting eye for this purpose), the weight of the QH has to be deducted from the SWL of the excavator. QHs fitted with lifting points/attachments are subject to the requirements of Lifting Operations and Lifting Equipment Regulations (LOLER) 1998.
If the QH is permanently attached to the excavator, then it can be treated as though it is part of the machine and should be thoroughly examined at least every twelve months, unless either there is an examination scheme which determines otherwise, or a competent person has set a different period, for example, due to its condition, or to particularly harsh operation (e.g. use with a hammer).
If the QH is not permanently attached to the excavator, then it should be treated as a lifting accessory and have a thorough examination every six months, or in accordance with an examination scheme.
Since the implementation of the Supply of Machinery Regulations 2008, there has been discussion between HSE, manufacturers, suppliers and user trade associations regarding the reclassification of couplers. This is an ongoing debate and further details will be provided, once a definitive legal position has been given via Europe. In the interim however, HSE categorises new QHs in accordance with the Supply of Machinery Regulations 2008 as interchangeable equipment.
This means each hitch should be CE marked and provided with a Declaration of Conformity (D of C), and this declaration fulfils the requirement of a thorough examination for the 12 months following the date on the D of C. After this date, thorough examination of the quick hitch is required if suitable for use in lifting operations. For QHs supplied by the excavator manufacturer as part of the original equipment, the D of C for the excavator is sufficient.
We hope you have found this article Quick hitch devices on excavators of interest, we cover quick hitches as part of our standard excavator training courses – here is a link to our main plant operator page. We can also provide a Quick Hitch course, which is a bolt on category to an existing Excavator licence, if you would like more details please do not hesitate to contact us.
Warm regards The Kentra Team